Resinex Instructions

1. Use only very dry wood
2. Activate the resin
3. Add resin to weighted-down wood in
vacuum chamber
4. Apply vacuum until no more bubbles
appear
5. Turn off vacuum
6. Allow wood to soak in resin for at least
twice as long as vacuum time
7. Wipe dry and wrap in alu foil, place in
oven at 110 C for 2-4 hours
8. Unwrap one block, cure for another
hour if still wet, then check again
9. Store in cool place once activated
(in plastic bottle and in A/C or fridge)

Here is a longer version of the same, with more detail added;

Pro Tip: For best results, plan to do several batches so you can activate the entire 3 kg bottle and re-use while fresh.

Prepare the wood:

1.       The wood needs to be very dry, preferably 2% moisture or less. Often wood stored in your house or shed will have too much moisture and needs to be dried. This can be done by gently heating the blocks in a toaster oven at 100 C for 24 hours, then placing the blocks in a zip lock bag or small airtight container while cooling down. Leaving them to cool out in the air will make them absorb moisture again while cooling now. Putting hot blocks in the stabilizing resin is a guaranteed way to fail, as the resin will partially harden and destroy the blocks.

2.       Avoid woods with high levels of natural oils, such as Rosewood and Cocobolo. Great candidates are woods with open grain and visible figure such as curly birch, maple burl and other fairly light-weight woods and burls.

3.       Native Australian timbers are harder to stabilize than European and American woods and will need extended time under vacuum and extended soak times. Seek advice from Australian experienced wood stabilisers for success on these woods and completely ignore advice related to woods such as maple, birch and oak which most online stabilizing advice is based on.

4.       Number a couple of the blocks with a sharpie and write down the weight so you can compare before/after weights when done.

Activate the Resin:

1.       The simplest and most secure way to activate the resin correctly is to activate the entire 3 kg bottle in one go as this ensures the correct ratio of activator to resin.

2.       To activate: The small bottle of activator product is exactly enough for 3 kg of resin. If using the entire bottle of 3 kg, pour in the activator product, close the bottle and shake. Leave for 30 mins and shake again. If the resin is cold, it will not activate properly, room temperature of 18-25 degrees is best. Once activated try to keep the solution cool and not in direct sunlight.

3.       Activate only what you need:

a.       If not using the entire 3 kg bottle: Only activate the amount of resin you will need to cover the wood blanks by 3-5 cm in the chamber, to extend the shelf-life of the rest of the resin.

b.       If activating less than the full 3 kg bottle, weight up exactly 2.1 grams of activator product per kg of stabilizing resin and shake well. (ratio is 2.1 grams per 1000 grams of resin, start by weighting the resin then accurately weight the activator)

4.       Any activated resin can be stored for re-use, but aim to keep it cool. Do not pour the left-over activated resin back in with the non-activated resin in the original bottle.

5.       Optional: The stabilising resin can be dyed with solvent-based dyes only, we recommend learning the process on your setup without dyes until you are comfortable with the results then add small amounts of dye and gradually increase the volume of dyes between batches.

6.       NOTE Activator has to be stored under 30 degrees C to avoid breaking down and activated resin should also be stored cool, well away from direct sunlight.

Stabilise:

1.       Place bone dry wood blanks in the stabilizing chamber and weight down to ensure the wood does not float to the top. Wood can be stacked on top of each other with no issues.

2.       Add the activated, well-mixed stabilising resin making the wood is fully submerged and the resin is at least 3-5 cm above the level of wood.

3.       Apply full vacuum and leave until all bubbles stop.

4.       Best practice is to first start pump with vacuum control valve open and then slowly close, to help with keeping the initial foaming under control. As the foam dies down, you can close the vacuum control valve and achieve full vacuum.

5.       The closer to full vacuum you can get, and the dryer the wood is, and the longer they are left in vacuum and then to soak, the better your stabilised blanks will be.

6.       Full vacuum is 29.92” at sea level, and you should aim for 29” but note that the higher you are above sea level, the lower “full vacuum” is. For instance in Brisbane or Melbourne at 29 meters elevation above sea level, full vacuum is 29.81” and in Lithgow at 950 m above sea level, full vacuum is only 26.71”. (Achieving full vacuum is not possible; you only aim to get as high vacuum % as possible in the elevation you are at)

7.       When there are no more bubbles, the wood blanks have been “emptied” for air and the pump has expelled this air from the chamber.

8.       Release the vacuum and then turn the pump off.

9.       Leave the wood blanks to soak in the resin for at least twice as long as they were under vacuum (**note separate section on Australian vs European woods**)

10.   If in doubt, leave them to soak for longer. Days or even weeks.

Curing:

1.       Remove the wood from the resin and let any resin drip off.

2.       Wrap each block in aluminium foil, individually so no two blanks touch each other. You can wrap several blocks together in a long strip of foil if making sure they have layers of foil separating them. Any blocks touching will come out as a single, solid block fused together.

3.       Pre-heat your oven to 110 degrees C. This needs to be fairly accurate, use a temperature sensor to read your oven and ignore the temperature dial on the stove as these often are 10+ degrees off. A thermocouple and digital reader is a good investment here.

4.       Too high temperature will not hurt the resin but it will make more resin come out of the blocks before it has time to cure so much better to keep the temperature as close to 110 C as possible.

5.       The inside of each block has to reach minimum 87-93 degrees C for a minimum of 10 minutes for full curing of the resin. This will take a couple of hours, if in doubt, leave the blanks for longer until you learn your setup.

6.       Test for complete curing: Using gloves, remove one block and peel back the foil. If you see any wet/liquid resin still, it is not ready so put it right back before it has time to cool and give it another hour before testing again.

Finishing the wood blanks:

1.       When the blocks are cured, remove from the stove and remove the foil.

2.       Allow blocks to cool.

3.       When cool, scrape, saw or sand off the excess resin for a cleaner-looking product.

4.       Sanding to 240 grit is a great way to show off the final product.

5.       Weight the control blocks and record difference in weight so you can refer to this later when comparing results across batches and types of wood. Be careful to remove excess resin but not the actual wood block to get an accurate “after” weight.

Clean-up:

·       Wash-up the chamber with normal dish-washing soap, rinse and dry.

·       Do not pour the activated resin back in with the un-activated resin in the bottle it came in.

·       You can store the activated resin in the bottle it came in, if empty.

·       Do not store activated resin in PVC or acrylic stabilising chambers or containers over time, it may slowly cure.

·       Glass, metal or even ceramic containers are ok, no need to cap as it will not evaporate. Important: Do not cap any glass container to avoid potential pressure-build up over time should the resin start to cure.

Storage

·       Store the activated resin in a fridge or air-conditioned room if possible for longer life. If the resin has not set, it is safe to re-use. If possible, store below 10 C.

·       Non-activated resin has a shelf-life of up to 18 months when stored below 10 C.

·       Temperatures in Australia can be extreme and significantly reduce shelf-life if the resin is allowed to cycle in temperature between cool nights and hot days. Fridge storage is the best bet and failing that, in a cool spot in an air-conditioned room.

Safety:

·       Both Activator and Stabilising Resin contain dangerous chemicals and proper care must be taken not be exposed to these chemicals. Do not inhale, touch or expose yourself or others to the activator powder, use gloves if touching any of the materials and dispose of in a safe way. This includes the activated resin and the bottles the products came in.

·       In summary; store cool, activate the resin and place in chamber without unnecessary handling.